Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
xro:lothrelectronicsstation [2019-01-13 16:11] xro |
xro:lothrelectronicsstation [2019-02-03 14:08] xro |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| * Backside Switch re-used on front | * Backside Switch re-used on front | ||
| * [[https://www.thingiverse.com/thing:2817722 | T12 Tip Holder]] | * [[https://www.thingiverse.com/thing:2817722 | T12 Tip Holder]] | ||
| - | * [[https://www.conrad.at/de/schuetzinger-seb-6452-ni-sw-sicherheits-laborbuchse-buchse-einbau-vertikal-stift-o-4-mm-schwarz-1-st-1537941.html| 2x Safety Laboratory Banana Jack]] | + | * [[https://www.conrad.at/de/schuetzinger-seb-6452-ni-sw-sicherheits-laborbuchse-buchse-einbau-vertikal-stift-o-4-mm-schwarz-1-st-1537941.html| 4x Safety Laboratory Banana Jack]] |
| * old external SCSI HDD Case | * old external SCSI HDD Case | ||
| * 2x 5pin Jumper-Wire Jack | * 2x 5pin Jumper-Wire Jack | ||
| * Switching power supply 24V / 3.2A, set to ~27V | * Switching power supply 24V / 3.2A, set to ~27V | ||
| + | * [[https://de.aliexpress.com/item/35-watt-elektronische-last-einstellbare-konstante-strom-aging-widerstand-batterie-spannung-kapazit-t-tester-LCD-spannung/32954356498.html | XY-FZ35 Electronic Load]] | ||
| + | * 1x USB Serial TTL Converter | ||
| + | * 3x Jumper Wires | ||
| + | === Manual === | ||
| + | |||
| + | [[:MiniElectronicsWorkStationManual]] | ||
| === Photos === | === Photos === | ||
| Line 18: | Line 24: | ||
| https://galley.realraum.at/index.php?/category/184 | https://galley.realraum.at/index.php?/category/184 | ||
| - | === Front === | + | === Blog Posts === |
| - | The front was lasercut to accommodate the different devices. | + | * https://wp.realraum.at/2019/01/lothr-mini-electronics-workbench/ |
| + | * https://wp.realraum.at/2019/02/lothr-mini-electronics-workbench-upgrade/ | ||
| - | * Black: cut with 100% 60W at 7mm/s | ||
| - | * Red: scan-engraved with 12% 60W at 100mm/s | ||
| - | {{ :xro:loetstationlabornetzteillothrbox2.svg |}} | + | === Front === |
| - | === Todo === | + | The front was lasercut to accommodate the different devices. |
| - | * add electronic load as third element in top slot | + | * Black: cut with 90% 60W at 10mm/s |
| + | * Red: scan-engraved with 18% 60W at 100mm/s | ||
| - | {{ :xro:loetstationlabornetzteillothrbox3_loadonly.svg |}} | + | {{ :xro:loetstationlabornetzteillothrbox3.svg |}} |
realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft