Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
realraum:minielectronicsworkstationmanual [2019-02-03 18:51] xro |
realraum:minielectronicsworkstationmanual [2020-01-04 16:23] (current) xro |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Manual for LoTHR Electronics Station ==== | ===== Manual for LoTHR Electronics Station ==== | ||
| + | Aka: Mini-TESLA | ||
| + | |||
| + | {{:realraum:qr_lothr_etech_manualwiki.png?direct&180|}} | ||
| + | ShortURL: http://shorturl.at/efoAE | ||
| + | |||
| + | **Main-Power-Switch for everything**: located at back of box. | ||
| ==== The Electric Load XY-FZ35 ==== | ==== The Electric Load XY-FZ35 ==== | ||
| Line 93: | Line 99: | ||
| - | ==== The Power Supply DS30V05A ==== | + | ==== The Power Supply RD-Tech DS30V05A ==== |
| * Current-Limit, setable in 0.001A increments | * Current-Limit, setable in 0.001A increments | ||
| Line 104: | Line 110: | ||
| See Manual stuffed into the back. | See Manual stuffed into the back. | ||
| - | {{ :realraum:dp30v5a_htb16b51jfxxxxb1xxxxq6xxfxxx7.jpg?direct&600 |}} | + | {{ :realraum:dp30v5a_htb16b51jfxxxxb1xxxxq6xxfxxx7.jpg?direct&700 |}} |
| - | {{ :realraum:dp30v5a_htb1maynjfxxxxc9xpxxq6xxfxxxl.jpg?direct&600 |}} | + | {{ :realraum:dp30v5a_htb1maynjfxxxxc9xpxxq6xxfxxxl.jpg?direct&700 |}} |
| ^ Buttons ^^ | ^ Buttons ^^ | ||
| Line 123: | Line 129: | ||
| [[http://www.quickochina.com/uploads/USERmanual-en.pdf|Link to english Manual]] | [[http://www.quickochina.com/uploads/USERmanual-en.pdf|Link to english Manual]] | ||
| - | |||
| - | ^Button ^ Use ^ | ||
| - | |CW | Lower value / Boostmode | | ||
| - | |CCW | Increase Value / Standby | | ||
| - | |Press | Select | | ||
| - | |Long Press | Menu or exit menu| | ||
| - | | CW while pressing | change TIP temperature profile | | ||
| - | | CCW while pressing | calibrate Tip (only on newer firmware version) | | ||
| If the station detects movement/temperature fluctuations of the tip, it will automatically exit standby mode. | If the station detects movement/temperature fluctuations of the tip, it will automatically exit standby mode. | ||
| - | === On / Off === | + | === Usage === |
| - | Just turn knob CW. | + | ^ Mode ^ How to get there ^ |
| + | | Hard-Off | Use power-switch right of device | | ||
| + | | On | Enable power-switch on the right and turn knob CW until on | | ||
| + | | Boost-Mode (+ ~60°C for ~5min) | Turn knob CW until device enters boost mode | | ||
| + | | Standby (~120°C) | Turn know CCW until device is in standby mode | | ||
| + | | Sleep (Soft-Off) | Turn knob CCW until sleep mode is selected | | ||
| + | | Set Temperature | Press knob once | | ||
| + | | Menu/Settings | Hold knob down | | ||
| + | | Change Tip Preset | Hold knob down while turning knob CW| | ||
| === Set Temperature === | === Set Temperature === | ||
| - | Press knob once and set temperature by turning knob. | + | - Press knob once |
| + | - set temperature by turning knob. | ||
| === Change Soldering Tip === | === Change Soldering Tip === | ||
| - | Press knob and turn CW. Then select tip and confirm with button press. | + | - Hold knob down while turning knob CW |
| - | + | - Then select tip and confirm with button press. | |
| - | === Boos Mode === | + | |
| - | + | ||
| - | Turn know CW. | + | |
| - | + | ||
| - | === Standby === | + | |
| - | Turn know CCW. | ||
| === Calibration === | === Calibration === | ||
| Get Solder-iron-tip temperature meter from TESTLA and go to menu and select calibration. | Get Solder-iron-tip temperature meter from TESTLA and go to menu and select calibration. | ||
realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft