Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
3dprinting:prusai3mk25 [2019-10-28 01:58] xro |
3dprinting:prusai3mk25 [2019-10-28 02:33] xro |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| * 2019-10-28: | * 2019-10-28: | ||
| * works and prints beautifully without problems or issues or things that needed fixing (tested with PrusaSlicer and SD-Card) | * works and prints beautifully without problems or issues or things that needed fixing (tested with PrusaSlicer and SD-Card) | ||
| - | * filament sensor PAT9125 does not work and needs to be disabled in firmware | + | * filament sensor PAT9125 works with MK25 firmware and correctly detects broken or run-out filament |
| - | * either sensor is dead or not supported in MK2.5 Firmware, since prusa only sells this type for MK3 | + | * print bed adhesion is good if nozzle is cleaned beforehand. |
| ==== Resources ==== | ==== Resources ==== | ||
| Line 22: | Line 22: | ||
| * [[https://help.prusa3d.com/article/3tSXh6nWJd-pinda-probe-testing | PINDA Probe]] | * [[https://help.prusa3d.com/article/3tSXh6nWJd-pinda-probe-testing | PINDA Probe]] | ||
| - | ==== How To Print (recommended way) ==== | + | ==== How To Print ==== |
| + | |||
| + | - Slice a ''.stl'' | ||
| + | - Pre-Print check | ||
| + | - Print ''.gocde'' using SD-Card or via USB | ||
| + | |||
| + | |||
| + | === Slice === | ||
| - Use PrusaSlicer on Würfel | - Use PrusaSlicer on Würfel | ||
| Line 28: | Line 35: | ||
| - Select Material (probably PrusamentPETG) | - Select Material (probably PrusamentPETG) | ||
| - Slice | - Slice | ||
| - | - Save GCODE to SD-Card | + | - Save GCODE to Disk |
| + | |||
| + | === Pre-Print Check === | ||
| + | |||
| + | * Clean print-bed | ||
| + | * Check removable magnetic steel-print-bed is flat and correctly seated | ||
| + | * Carefully clean nozzle while nozzle is in the air and half-way heated by using cool metal pliers and removing softened filament without scratching anything | ||
| + | * Check you have the right filament inserted (the one you sliced for) | ||
| + | |||
| + | === Print using SD-Card === | ||
| + | |||
| + | - Eject SD-Card from Printer and put into Würfel | ||
| - if SD-Card Reader on front of Würfel does not work, disconnect and reconnect USB-Cable | - if SD-Card Reader on front of Würfel does not work, disconnect and reconnect USB-Cable | ||
| - | - Print from SD-Card | + | - Copy to SD-Card |
| - | - (after plugging SD-Card back into printer) | + | - Unmount SD-Card |
| + | - Plug SD-Card back into Printer | ||
| + | - Start print from SD-Card in printer menu | ||
| + | |||
| + | === Print via USB === | ||
| + | |||
| + | - Start Pronterface (Pronsole in Graphics Menu) | ||
| + | - Load ''.gcode'' file saved earlier | ||
| + | - ensure USB-cable is connected | ||
| + | - Start print | ||
| + | |||
| + | === Print via Octoprint === | ||
| + | TODO | ||
| ====== Specs and Settings ====== | ====== Specs and Settings ====== | ||
realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft