Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
realraum:minielectronicsworkstationmanual [2019-02-03 14:48] xro |
realraum:minielectronicsworkstationmanual [2020-01-04 16:23] (current) xro |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Manual for LoTHR Electronics Station ==== | ===== Manual for LoTHR Electronics Station ==== | ||
| + | Aka: Mini-TESLA | ||
| + | |||
| + | {{:realraum:qr_lothr_etech_manualwiki.png?direct&180|}} | ||
| + | ShortURL: http://shorturl.at/efoAE | ||
| + | |||
| + | **Main-Power-Switch for everything**: located at back of box. | ||
| ==== The Electric Load XY-FZ35 ==== | ==== The Electric Load XY-FZ35 ==== | ||
| Line 17: | Line 23: | ||
| === Settings === | === Settings === | ||
| + | |||
| + | {{ :realraum:htb13kozxpduk1rjsszdq6xglpxay.jpg?direct&400|}} | ||
| ^ Protection Settings °° | ^ Protection Settings °° | ||
| Line 24: | Line 32: | ||
| | OTP | over-temperature protection (at > 80°C, LCD flickers) | | | OTP | over-temperature protection (at > 80°C, LCD flickers) | | ||
| | LVP | undervoltage protection (default 1.5V) \\ When discharging a battery, set this to prevent damage to the battery | | | LVP | undervoltage protection (default 1.5V) \\ When discharging a battery, set this to prevent damage to the battery | | ||
| - | |||
| - | {{ :realraum:htb13kozxpduk1rjsszdq6xglpxay.jpg?direct&400|}} | ||
| - | |||
| The electronic load automatically saves the switching state before shutting down and resumes with the last state (power == on/off) | The electronic load automatically saves the switching state before shutting down and resumes with the last state (power == on/off) | ||
| - | |||
| - | |||
| Discharge capacity Statistics: | Discharge capacity Statistics: | ||
| Line 96: | Line 99: | ||
| + | ==== The Power Supply RD-Tech DS30V05A ==== | ||
| - | ==== The Power Supply DS30V05A ==== | + | * Current-Limit, setable in 0.001A increments |
| + | * Voltage-Lmit, setable in 0.01V increments | ||
| + | * max 5A (but current power supply limits to 72W. Need more? Go to TESLA) | ||
| + | * max 26V (would be max 30V but is Buck-Converter and poewr supply only supplies 29V. Need more? Go to TESLA) | ||
| - | ==== The KSGEr solering station ==== | + | === Usage === |
| + | |||
| + | See Manual stuffed into the back. | ||
| + | |||
| + | {{ :realraum:dp30v5a_htb16b51jfxxxxb1xxxxq6xxfxxx7.jpg?direct&700 |}} | ||
| + | {{ :realraum:dp30v5a_htb1maynjfxxxxc9xpxxq6xxfxxxl.jpg?direct&700 |}} | ||
| + | |||
| + | ^ Buttons ^^ | ||
| + | | Set (short press) | Begin or Confirm/End setting current/voltage limit) | | ||
| + | | EncoderKnob Press | Go to next Digit | | ||
| + | | EncoderKnob CW | increase digit | | ||
| + | | EncoderKnob CCW | decrease digit | | ||
| + | | Set (long press) | open additional settings screen \\ program memory locations | | ||
| + | | M1 | recall stored settings from memory location 1 | | ||
| + | | M2 | recall stored settings from memory location 2 | | ||
| + | |||
| + | ==== T12 solering station (KSGER, Quicko) ==== | ||
| Software Version: 2.09 | Software Version: 2.09 | ||
| Line 105: | Line 128: | ||
| Hardware Version: .... | Hardware Version: .... | ||
| - | === On / Off === | + | [[http://www.quickochina.com/uploads/USERmanual-en.pdf|Link to english Manual]] |
| + | |||
| + | If the station detects movement/temperature fluctuations of the tip, it will automatically exit standby mode. | ||
| + | |||
| + | === Usage === | ||
| + | |||
| + | ^ Mode ^ How to get there ^ | ||
| + | | Hard-Off | Use power-switch right of device | | ||
| + | | On | Enable power-switch on the right and turn knob CW until on | | ||
| + | | Boost-Mode (+ ~60°C for ~5min) | Turn knob CW until device enters boost mode | | ||
| + | | Standby (~120°C) | Turn know CCW until device is in standby mode | | ||
| + | | Sleep (Soft-Off) | Turn knob CCW until sleep mode is selected | | ||
| + | | Set Temperature | Press knob once | | ||
| + | | Menu/Settings | Hold knob down | | ||
| + | | Change Tip Preset | Hold knob down while turning knob CW| | ||
| === Set Temperature === | === Set Temperature === | ||
| + | |||
| + | - Press knob once | ||
| + | - set temperature by turning knob. | ||
| === Change Soldering Tip === | === Change Soldering Tip === | ||
| - | === Boos Mode === | + | - Hold knob down while turning knob CW |
| + | - Then select tip and confirm with button press. | ||
| === Calibration === | === Calibration === | ||
| + | Get Solder-iron-tip temperature meter from TESTLA and go to menu and select calibration. | ||
realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft