This is an old revision of the document!
Lulzbot Taz4
3D Drucker der derzeit im Raum ist und super cool und verwendbar: Lulzbot TAZ4
Specs TAZ 4.1 – Test Acceptance Record | |
---|---|
max build Area | 298mm x 275mm x 250mm |
Resolution: | >=0.1mm |
max Heatbed Temp | 120°C |
max build speed | 200mm/s |
Firmware | Marlin 2014-Q3 |
Electronics | RAMBo 1.3L |
Serial# | KT-PR0016-7986 |
steps/mm X | 100.5 |
steps/mm Y | 100.5 |
steps/mm Z | 400 |
steps/mm E0 | 842 |
Nozzle
currently mounted Nozzle | |
---|---|
Diameter | 0.35mm |
Max Temperature | 240°C (exceed at risk of DAMAGE) |
Type | Budaschnozzle 2.0c |
Current Firmware Settings
2015-11-12
Value | Setting from LCD |
---|---|
Autotemp | Off |
Autotemp Min | 210 |
Autotemp Max | 250 |
Autotemp Fact | 0.10 |
PID-P | 6.00 |
PID-I | 0.30 |
PID-D | 125.00 |
PID-C | 1 |
Zoffset | 0 |
Accel | 500 |
Vxy-jerk | 8 |
vz-jerk | 0.40 |
ve-jerk | 10 |
vmax x | 800 |
vmax y | 800 |
vmax z | 8 |
vmax e | 50 |
amax x | 9000 |
amax y | 9000 |
amax z | 100 |
amax e | 10000 |
a-retract | 3000 |
xsteps/mm | 100.50 |
ysteps/mm | 100.50 |
zsteps/mm | 1600 |
Esteps/mm | 842.0 |
E1steps/mm | 800.00 |
HeatBed Autotune
2015-11-12
bias: 41 d: 41 min: 64.86 max: 65.28 Ku: 250.58 Tu: 18.09 Clasic PID Kp: 150.35 Ki: 16.62 Kd: 339.93 PID Autotune finished! Put the Kp, Ki and Kd constants into Configuration.h
Tipps
PreHeating
On cold days the heatbed glass can lag about 10min behind the heatbed temperature. Lot's more mass that needs to be heated. Waiting a while helps with the print.
Manual
Print Profiles
can be found in
LulzBot
Folder.
Model Design
You wall thickness should be a multiple of the nozzle size.
If you are printing thing walls for cookie cutters, make sure your wall is thick enough to be printed. You can check in cura in the layers-view.
Materials
Correct profiles for each material can be found in: ~/lulzbot/cura profiles/
currently in realraum
- HIPS 3mm white
- t-glase clear 3mm
- t-glase red 3mm
- PLA deep blue 3mm
- Stainless Steel PLLA (proto-pasta)
- Cleaning Filament
- clear PLA
- clear yellow PLA
- nGen Black von colorFabb
See the Lulzbot Filament Guide on print-settings for various materials.
See also the Lulzbot Cura Profiles Page
Printing with Nylon
Nylon does not stick to the print-bed. Not even with the heat turned on.
- Use Glue-Stick on printbed beforehand. Glue-Stick is in black LulzBot Bag, Please store there again after use.
- Do NOT heat the printbed. That just leads to the Glue drying out early and the print failing.
- Glue-Stick-glue is water-solvable. Clean printbed with wet wettex and paper afterwards!.
Nylon should regularly dried at 80°C for 7 Hours and stored in airtight container with desiccant. (Under the Table)
what can be printed ?
Everything with a filament diameter of 3mm (no less and no more) and extrusion temperature below 238°C that does not clog 0.35mm nozzles, like wood-,stainless-steel-,conducitve,“magnetic”-filament does.
about 1.75mm filament
To print 1.75mm filament, a different PTFE-Tube would be needed. However, Lulzbot no longer manufactures or sells them. Conceivably they are easy to make yourself from aluminum or PTFE with a lathe. Seeing as their newest Hexagon Hotend does not even mention the option of printing anything but 3mm filament, Lulzbot seems to have completely abandoned support for anything other than 3mm filament.
Quote from Lulzbot-Sales 2015-09-25:
I do apologize, but we no longer carry those tubes. We have tested several filaments on our printers, and prefer the 3 mm size, as it much easier to work with.