Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
roomauto:deckenlichter.md [2017-01-16 22:52]
xro
roomauto:deckenlichter.md [2017-02-15 14:19] (current)
xro
Line 55: Line 55:
 * switching ceiling light power on/off is probably not as quick or nice-to-look-at as having planned [ESP8266 based H801](https://​www.aliexpress.com/​item/​RGBWW-Strip-WiFi-Controller-1-Port-Control-200-Lights-Communicate-with-Android-Phone-Via-WLAN-to/​32502007408.html) do it * switching ceiling light power on/off is probably not as quick or nice-to-look-at as having planned [ESP8266 based H801](https://​www.aliexpress.com/​item/​RGBWW-Strip-WiFi-Controller-1-Port-Control-200-Lights-Communicate-with-Android-Phone-Via-WLAN-to/​32502007408.html) do it
  
-Project ​CeilingLight on Steroids+Project ​FancyLights
 -------------------------------- --------------------------------
  
Line 108: Line 108:
      * action/​ceilingN/​defaultlight ​ {"​r":​int,​ "​g":​int,​ "​b":​int,​ "​cw":​int,​ "​ww":​int} ​ | N={1..6,​All},​ int={0..1000}      * action/​ceilingN/​defaultlight ​ {"​r":​int,​ "​g":​int,​ "​b":​int,​ "​cw":​int,​ "​ww":​int} ​ | N={1..6,​All},​ int={0..1000}
   * (done) provide backup interface. e.g. telnet   * (done) provide backup interface. e.g. telnet
-  * secure ​backup telnet interface+  * (done) ​backup telnet interface
  
-4. test in dry state+4. (done) ​test in dry state
   * startup behaviour: PWM pins start in INPUT direction, all channels except R- light up for 700ms \\ --> prefer solution where H801 soft-disables the LEDs and itself stays powered versus being powered on/off constantly   * startup behaviour: PWM pins start in INPUT direction, all channels except R- light up for 700ms \\ --> prefer solution where H801 soft-disables the LEDs and itself stays powered versus being powered on/off constantly
   * startup behaviour: configured default light state apply'​s really fast after about y1.4s (not after blinking due to INPUT direction though)   * startup behaviour: configured default light state apply'​s really fast after about y1.4s (not after blinking due to INPUT direction though)
Line 117: Line 117:
   * Telnet configuration works really well   * Telnet configuration works really well
   * spiffs flash-time pre-configuration works really well   * spiffs flash-time pre-configuration works really well
-4. test in indirect ceiling illumination configuration+4.(done) ​test in indirect ceiling illumination configuration
   * Strip1 (RGB+CW) width: 12mm   * Strip1 (RGB+CW) width: 12mm
   * Strip2 (WW) width: 9.5mm   * Strip2 (WW) width: 9.5mm
 +  * all in all not bright enough for that and not diffuse enough
 4. (done) test in ceiling light enclosure 4. (done) test in ceiling light enclosure
   * WIFI works really well, surprisingly no problem   * WIFI works really well, surprisingly no problem
Line 128: Line 129:
   * Things learned   * Things learned
     * prefer splice WarmWhite from VCC, not from V+ where it passes the PCB     * prefer splice WarmWhite from VCC, not from V+ where it passes the PCB
 +    * Red and Green is switched on RGB+CW Strip
     * vor-Auflegen funktioniert nicht gut -> aufzeichnen     * vor-Auflegen funktioniert nicht gut -> aufzeichnen
     * use 12mm 5pin clip-connectors for 12mm wide 5pin RGBW Led strip (not 10mm) -> ordered 12mm     * use 12mm 5pin clip-connectors for 12mm wide 5pin RGBW Led strip (not 10mm) -> ordered 12mm
Line 137: Line 139:
     * arrange power supply in corner of edges, where they don't cast shadow if possible     * arrange power supply in corner of edges, where they don't cast shadow if possible
     * arrange H801 in center when possible     * arrange H801 in center when possible
-5. change golightctrl so it can control H801 +5. (almost done) change golightctrl so it can control H801 
-6. install in ceiling lights+6. (1/6 done) install in ceiling lights
 7. put CW-LEDs currently in one ceiling lights into MaSha  ​ 7. put CW-LEDs currently in one ceiling lights into MaSha  ​
-WW-LEDs in all Ceiling lights as Simple-Light ​ +WW-LEDs in all Ceiling lights as Simple-Light
 RGB+CW+WW-Fancy-Lights int all Ceiling lights RGB+CW+WW-Fancy-Lights int all Ceiling lights
 +8. modify 20W RGB+WW Flodding Lights with H801 and indirectly illuminate ceiling
  
-Project ​Switches as Robust Fallback+Project ​BasicLights
 ----------------------------------- -----------------------------------
  
-**Plan:​** ​connect Relay directly to Teensy µC+**Plan:​** ​separate lights which work really really reliably
  
-**Working on it:**  [xro](doku.php?​id=xro:xro)+**Working on it:**  [equinox](doku.php?​id=equinox:equinox)
  
-**Status**: ​Concept+**Status**: ​WIP
  
 **TODO** **TODO**
  
-1. change teensy firmware to switch LOW for light-on +1. (1/6 done) install Tanbaby LED Lights in Ceiling Lights 
-2. ensure H801 firmware ​acts transparentPower on -> Light, Power off -> no light +2. (presumably done) write firmware ​for Teensy2.0 
-3. always cut power if physical switches are used +3. (almost done) create enclosure with Teensy2.0 and buttons 
-4. change golightctrl to  +4. install and connect power 
- * send soft-off to H801 if web-buttons are sued +5. interface with RasperryPi in a way that 
- ​* ​cut power via relay if physical buttons are used +  Raspberry can switch lights 
- ​* ​cut power if presence=false +  Teensy2.0 does not depend on Raspberry ​power 
-5connect Relay directly to Teensy µC+  * Raspberry and Teensy2.0 can be disconnected from each other / from power in case of error on each
realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft
  • /var/lib/dokuwiki/data/pages/roomauto/deckenlichter.md.txt
  • Last modified: 2017-02-15 14:19
  • by xro