This is an old revision of the document!


ShortURL: http://shorturl.at/efoAE

Main-Power-Switch for everything: located at back of box.

The Electric Load XY-FZ35

Do not exceed maximums

Max Voltage 25V
Max Current 5A
Max Power Wattage 35W

Settings

OVP overvoltage protection (default 25.2V)
OCP overflow protection (default 5.10A)
OPP power protection (default 35.5W)
OTP over-temperature protection (at > 80°C, LCD flickers)
LVP undervoltage protection (default 1.5V)
When discharging a battery, set this to prevent damage to the battery

The electronic load automatically saves the switching state before shutting down and resumes with the last state (power == on/off)

Discharge capacity Statistics:

the load current is not zero start statistics, until the next load current is zero, it is believed that the completion of a discharge process, statistical end

Discharge time Statistics:

from the current is not zero start statistics, to the next load current is zero, think that the completion of a test process, statistical end;

Set maximum Capacity (OAH):

When the OAH function is started, when the load discharge capacity is higher than the maximum capacity set, the electronic load stops
automatically and flashes to display “OAH”, and when the OAH alarm is lifted, the capacity statistics are automatically emptied

Set the maximum discharge time (OHP):

When the OHP function is started, when the load running time is greater than the maximum discharge time set, the electronic load stops
automatically and flashes to display “OHP”, and when OHP alarm is lifted, the time statistics are automatically emptied;

Note: If neither OAP or OHP are set, the electronic load will record the discharge capacity and discharge time. When the OHP function is turned on, the running time of the electronic load is the countdown mode

Data group Features
DAT0 Flashing shows only the capacity value and running time of the previous stage, and does not accumulate in the next run
DAT1 Flashing shows the capacity value and running time of the previous stage and will accumulate in future runs

Serial Interface

Connect your PC via USB port above FZ35. Use serial console with 9600 8 N 1

Serial Commands
start Start upload
stop Stop upload
on Turn on Load features
off Turn off Load features
x.xxA Set load current
LVP:xx.x Set down Undervoltage
OVP:xx.x Set over pressure
OCP:x.xx Set over flow
OPP:xx.xx Set over power
OAH:x.xxx Set maximum capacity
OHP:xx:xx Set maximum discharge time
read Read product parameter settings
Data upload format

No alarm status:

Load supply voltage, load current, capacity value, discharge time;

11.90V,0.11A,0.004Ah,00:02 à Load voltage 11.90V, load current 0.11A, capacity 0.004Ah, discharge time 00:02;

Note: If the maximum discharge time is turned on, 00:02 indicates a countdown;

Alarm Status

Upload Alarm status code (OVP/OCP/OPP/LVP/OAH/OHP/OTP)

Read product parameter settings

OVP:25.2, OCP:5.10, OPP:35.5, LVP:1.50,OAH:0222,OHP:00:00,

Overvoltage, overcurrent, over power, undervoltage, maximum capacity, maximum discharge time

The Power Supply DS30V05A

  • Current-Limit, setable in 0.001A increments
  • Voltage-Lmit, setable in 0.01V increments
  • max 5A (but current power supply limits to 72W. Need more? Go to TESLA)
  • max 26V (would be max 30V but is Buck-Converter and poewr supply only supplies 29V. Need more? Go to TESLA)

Usage

See Manual stuffed into the back.

Buttons
Set (short press) Begin or Confirm/End setting current/voltage limit)
EncoderKnob Press Go to next Digit
EncoderKnob CW increase digit
EncoderKnob CCW decrease digit
Set (long press) open additional settings screen
program memory locations
M1 recall stored settings from memory location 1
M2 recall stored settings from memory location 2

T12 solering station (KSGER, Quicko)

Software Version: 2.09

Hardware Version: ….

Link to english Manual

If the station detects movement/temperature fluctuations of the tip, it will automatically exit standby mode.

Off / Sleep / Standby / Off

Mode How to get there
Hard-Off Use power-switch right of device
On Enable power-switch on the right and turn knob CW until on
Boost-Mode (+ ~60°C for ~5min) Turn knob CW until device enters boost mode
Standby (~120°C) Turn know CCW until device is in standby mode
Sleep (Soft-Off) Turn knob CCW until sleep mode is selected
Set Temperature Press knob once
Menu/Settings Hold knob down
Change Tip Preset Hold knob down while turning knob CW

Set Temperature

  1. Press knob once
  2. set temperature by turning knob.

Change Soldering Tip

  1. Hold knob down while turning knob CW
  2. Then select tip and confirm with button press.

Calibration

Get Solder-iron-tip temperature meter from TESTLA and go to menu and select calibration.

realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft
  • /var/lib/dokuwiki/data/attic/realraum/minielectronicsworkstationmanual.1549217548.txt.gz
  • Last modified: 2019-02-03 19:12
  • by xro