This is an old revision of the document!
Use Cleaning Filament when changing to a filament with a different extrusion temperature.
Otherwise lower-temp filament will charcoal inside the hotend at higher temperatures which can obsctruct the hot-end and create back-pressure and can be almost impossible to clean out.
3D Printing Materials aka Filament in realraum
-
- Colors in r3: Black, Purple, Silver (,Blue if you ask DDD)
- Extrusion-temp: 230°C
- 2.85mm Spool Length 750g: ~95m
- 2.85mm Spool Length 2200g: 270m
- normal price, only slightly more expensive than ABS
- least warping so good for precise prints
- sticks really well to printbed
- recommended for big and precise prints
-
- Colors in r3: Yellow
- Extrusion-temp: 230°C
- SORRY only samples in r3
- IF YOU USE A SAMPLE: document result using photos!!!
- expensive price
- like nGen
- recommended for prints where layering should be hard to see
-
- Color: translucent white
- Extrusion-temp: 230°C - 240°C
- 3mm Spool Length: 62.7m
- normal price
- awesome material durability and strength
- needs glue and no printbed heat to stick. even so has tendency of warping on large ground surfaces and thus getting loose
- recommended if cheap, small or very durable prints are needed
-
- Colors in r3: clear, red
- Extrusion-temp: 230°C
- 3mm Spool Length: 56m
- double price
- translucent
- brittle
-
- Colors in r3: deep blue
- Extrusion-temp: 195-215°C
- 3mm Spool Length: ~125m
- normal price
-
- Color: steel gray
- Extrusion-temp: 195-220°C
- 2.85mm Spool Length: ~30m
- 5x normal price, since it's really expensive to buy
actually more than 10 times as expensive as HIPS per meter. - brittle on small features but durable like PLA and heavy on bigger pieces
- sticks really well on printbed. do not use glue or can forget about getting your print off the bed
-
- Color: translucent white
- Extrusion-temp: 150-300°C
- 3mm Spool Length: ~5m
- use only for cleaning and when changing filaments
-
- Colors in r3:
white - Extrusion-temp: 230°C
- Spool Length: ~140m
- normal price
- nice material strength
- warps on large surface area
- needs raft for less than 4cm² ground surface
- PLA 1.75 (for Witbox)
- normal price
- Colors in r3: blue, …..
- Extrusion-temp: 220°C
- ABS
- normal price
See the Lulzbot Filament Guide on print-settings for various materials.
See also the Lulzbot Cura Profiles Page
Cost and Prices
- Cost is per meter filament (2.85..3mm ø)
- Experimental: Cost per g (As we have different filaments widths, this is an attempt at simplification)
- if g and m cost disagree, choose cost per m or the average between the two at your discretion
- Cura (or slicer of your choice) tells you how many meters and g you will need
- We pay per started meter. e.g. you upround
- Please feed the cat next to the printer with the € before printing
for members
in gramm
- normal price material: 0.06€ per gram
- double price material: 0.12€ per gram
- 5x normal price material: 0.30€ per gram
in m for 3mm Filament (Lulzbot)
- normal price material: 0.50€ per started meter
- double price material: 1.00€ per started meter
- 5x normal price material: 2.50€ per started meter
in m for 1.75mm Filament (everything else)
- normal price material: 0.30€ per started meter
- double price material: 0.60€ per started meter
- 5x normal price material: 1.50€ per started meter
for guests
in gramm
- normal price material: 0.12€ per gram
- double price material: 0.24€ per gram
- 5x normal price material: 0.60€ per gram
in m for 3mm Filament (Lulzbot)
- normal price material: 1.00€ per started meter
- double price material: 2.00€ per started meter
- 5x normal price material: 5.00€ per started meter
in m for 1.75mm Filament (everything else)
- normal price material: 0.60€ per started meter
- double price material: 1.20€ per started meter
- 5x normal price material: 3.00€ per started meter
realraum Graz, Brockmanngasse 15, 8010 Graz, realraum - Verein für Technik in Kultur und Gesellschaft